segunda-feira, 17 de agosto de 2015

Mesa dobrável em palete - Folding table on pallets

Bom dia Amigos!

Good morning friends!
To friends from outside Brazil, below is a translation via GoogleTranslate.

Segue abaixo uma dica de como fazer uma mesa dobrável ocupando assim pouquíssimo espaço quando não esta sendo utilizada.
Vamos aos materiais necessários:
Materiais:
Uma tampa de palete do tamanho que achar melhor, a nossa é da seguinte medida: 66x96cm;
Dois pedaços de ripão ou similar, sendo: um do tamanho do comprimento do palete (que será preso a parede) e outro da medida da altura desejada;
Conjunto com duas dobradiças e seus respectivos parafusos;
Lixa para madeira;
Verniz - pincel e água raz;
02 - Parafusos e bucha S8 (pode ser maior, menor não é recomendável)
Broca de concreto 8, e broca 8 madeira, broca 1/2" madeira
Nível - não é obrigatório

Ferramentas:
Furadeira, pincel, chave de fenda ou philips (depende dos seus parafusos), serrote ou similar, trena ou metro,

Como fazer:
Lixar todas as partes de madeira;
Medir um dos ripões e corta-lo no comprimento do palete;
Envernizar todas as peças.

Faça dois furos no ripão que irá ser preso na parede, se quiser embutir os parafusos, aumente um pouco o furo com a broca 1/2", tome cuidado para não atravessar toda a madeira. Depois com os furos prontos, marque na parede, de preferência com o auxilio de um nível, utilize a furadeira e a broca 8 para fazer os buracos.
No momento de fazer os buracos na parede, utilize a fita métrica ou o metro para colocar na altura desejada.
Fixe a madeira a parede;
Fixe as dobradiças na madeira que esta na parede, de preferência nas laterais da madeira.
Coloque o tampo em cima da madeira, encostando bem o tampo na parede e fixe as dobradiças na parte de baixo.
Agora é a hora de cortar a madeira que irá segurar a sua mesa quando esta estiver aberta.
Abra a mesa e meça a altura que deverá ter o ripão. No meu caso utilizo somente um, mas você poderá querer um de cada lado, ai fica ao seu critério.
Pronto, sua mesa já pode ser utilizada.
Cadastre-se em nosso blog e receba sempre dicas interessantes e de baixo custo.
Abraços, 

César H. Zanatto
#mesadepalete #mesadobrável #palete 


Escolha do Palet

Lixando os lados

Lixando os lados


Escolhendo a madeira que será presa a parede

Fazendo os furos na parede

Fixando apoio na parede

Mesa pronta, já lixada e envernizada

Aqui ficando em ângulo para prancheta de desenho

Fixa como mesa

Dobrada sem ocupar muito espaço
The following is a tip on how to make a folding table taking so very little space when not in use.
Let the necessary materials:
Materials:
A pallet cap the size you think is best, ours is the following measure: 66x96cm;
Two pieces of ripão or similar, as follows: a pallet length size (which is attached to the wall) and the other measuring the desired height;
Together with its respective two hinges and screws;
Sanding wood;
Varnish - brush and water reason;
02 - Screws and S8 bushing (can be higher, lower is not recommended)
Concrete drill 8, and 8 drill wood, drill 1/2 "wood
Level - is not required

Tools:
Drill, brush, screwdriver or philips (depends on its screws), saw or similar, measuring tape or meter,

How to:
Sanding all wood pieces;
Measure one of ripões and cut it to length of the pallet;
Varnish all parts.

Drill two holes in ripão that will be stuck on the wall, if you want to embed the screws, increase a little hole with the drill 1/2 ", be careful not to cross any wood. Then with the finished bore, mark the wall, preferably with the help of a level, use the drill and the drill 8 to make the holes.
When making the holes in the wall using a tape measure or meter to place the desired height.
Secure the timber wall;
Attach the hinges on wood that this wall, preferably on the sides of the timber.
Put the lid on the timber and abutting the top wall and secure the hinges at the bottom.
Now is the time to cut the timber that will hold your table when it is open.
Open the table and measure the height that should have ripão. In my case I use only one, but you might want one on each side, there is up to you.
There, your desk can now be used.
Join our blog and always receive interesting and inexpensive tips.
Hugs,

César H. Zanatto